This flag was added to VP8 to allow a mode where MB-level skipping
was not allowed, saving a bit per mb. It was never used in practice,
and hasn't been tested in VP9, so remove it.

Change-Id: Id450ec6904c6d06c1919508e7efc52d05cde5631

tx_type == DCT_DCT check is an implementation detail of iht_add. Also
adding dequant_add_y function with explicit DCT_DCT check inside.

Change-Id: Ia3cb0225601752cdef0ff6f0acd3a09d9dbd8938

In decoder, the scaling calculation, such as (mv * x_num / x_den),
is fairly time-consuming. In this patch, we check if the scaling
happens or not at frame level, and then decide which function to
call to skip scaling calculation when no scaling is needed. Tests
showed a 3% decoder performance gain.

Change-Id: I270901dd0331048e50368cfd51ce273dd82b8733

Now that the predictor is the dest, we do not need the
extra parameters.

Change-Id: I31e2c3d2015f4a1cd12e7f04536d8db478582a0a

Using regular 0 and 1 constants now.

Change-Id: Ie763503cbb727847cc8f1d6506cd6f2ee607f056

This is the first CL with vp9_reader changes. All another macro
definitions will be replaced after.

Change-Id: I1c6bd9c9a612ec1663d484d6adb4fb720af54063

Keyframes don't set this variable, so it would use the last set
values from inter frames.

Change-Id: Ie1ef45ece2c44b21b5d55f6cea9f7d6e7a445692

With this, the RD loop properly supports rectangular blocks.

Change-Id: Iece79048fb4e84741ee1ada982da129a7bf00470

Static threshold results slightly up (+0.1% on derf), probably b/c
we now take the filter (sharp/lowpass) into account for the breakout
decision.

Change-Id: I9f597601da434205142afd05f32690e7ba8fd690

Change-Id: Ieaec2c48f3752b8558ba051caaf4ba2ab0e9e84d

Using ROUND_POWER_OF_TWO macro, using array initialization syntax for
less code.

Change-Id: I661453a6b29a9046fcff0a3f18fccb452b5eb39d

Now that the predictor is the dest, we do not need the
extra parameters.

Change-Id: I78db73d39b5aff62f15303f3d51ad2797eae74b6

Change-Id: I697514efd6024e1b4153bbde58ae5e323b030981

Change-Id: I1f2dbf04a0140a7cc2060b0a9efb4ed8e5270d3d

This is work-in-progress, it implements multiple ARF
encoding behind an experimental flag.

It adds the ability to insert multiple ARF frames into a
single ARF group. This patch implements the reordering
of the coded frames, and implements a fixed-length coding
pattern. It applies a fixed quantizer strategy based on
where the frame is in the coding sequence.

Further work to modify the rate control strategy is
ongoing and will be submitted via a set of future patches.

In this first step, each ARF group is recursively
bisected and an ARF frame added at that position in the
sequence. The recursion continues until ARF frames are
within MIN_GF_INTERVAL frames.

The code sits behind the "multiple-arf" experimental
flag ("CONFIG_MULTIPLE_ARF"). The experimental flag
"oneshotq" ("CONFIG_ONESHOTQ") also needs to be enabled
for this patch to work correctly.

Change-Id: Ie473b05ebb43ac473c0cfb659b2b8042823085e2

Removing redundant code.

Change-Id: I71bfc40a1fb06d8e3149ed5400aa4dfd87a51aac

Change-Id: I7d3b2ef26aba3dfb1d5c83309aab2024e04ee819

Combine superblock inter predictors into a unified function that
allows configurable block width and height. The inter predictions
of block sizes smaller than 16x16 are handled differently. To be
continued on merging them later.

Change-Id: I14075959dd5e221f00c205c99ca35c1c31ef728e

Change-Id: I8fff2216c169c872f7073e66357e400f78a3445d