The macro block mode info context originally contained an
entry for each 16x16 macroblock. In VP9 each entry refers
to an 8x8 region not a macro block, so the naming is misleading.

This first stage clean up changes the names of 3 entries in the
structure to remove the mb_ prefix.

TODO clean up the nomenclature more widely in respect of
mbmi and bmi.

Change-Id: Ia7305c6d0cb805dfe8cdc98dad21338f502e49c6

Don't do vertical or horizontal splits if subsize < min_partition_size,
except for edge blocks where it makes sense.

Change-Id: I479aa66ba1838d227b5de8312d46be184a8d6401

Adding set_skip_context() function used from both encoder and decoder.

Change-Id: Ia22cfad3211a00a63eb294f64f857b78f4aa9b85

There will be another change set to rename BLOCK_SIZE_TYPE enum to
BLOCK_SIZE.

Change-Id: I8d1dfc873d6186fa5e554262f5169e929978085e

It represents the minimum partition size, so don't split if
bsize == min_partition_size .

Change-Id: Id77c32d6afef7d2ddec0368eaae18fb13227d30e

Loop filter configuration doesn't belong to macroblock, so moving it from
MACROBLOCKD to VP9_COMMON. Also moving the declaration of loopfilter struct
from vp9_blockd.h to vp9_loopfilter.h.

Change-Id: I4b3e34be9623b47cda35f9b1f9951f8c5b1d5d28

The set_offsets call is necessary inorder to set the
mode_info_context ptr correctly.

Change-Id: I644910cc5bacc50ee9cd78458843274ad8ee636d

Moving this block of code into a function makes the
code easier to read and change.

Change-Id: If4ede570cce1eab1982b188c4d3e4fd3d4db236e

Different partitionings were not being evaluated against
best_rd and there were unnecessary calls to RDCOST. This
could have resulted in a non-optimal partioning being
selected.

I simplified the variables used to track the rate,
distortion and RD values throughout the function.

Change-Id: Ifa7085ee80d824e86791432a5bc6d8fea5a3e313

The low precision 32x32 fdct has all the intermediate steps within
16-bit depth, hence allowing faster SSE2 implementation, at the
expense of larger round-trip error. It was used in the rate-distortion
optimization search loop only.

Using the low precision version, in replace of the high precision one,
affects the compression performance by about 0.7% (derf, stdhd) at
speed 0. For speed 1, it makes derf set down by only 0.017%.

Change-Id: I4e7d18fac5bea5317b91c8e7dabae143bc6b5c8b

There was no benefit having this function. For example, inside
read_switchable_filter_type switchable filter context was calculated twice.

Change-Id: I79cd5bf95cbc0f6d8bf91a2e32289e01b18dcff1

Change-Id: I3aae21e88b876d53ecc955260479980ffe04ad8d

Adds a speed feature to skip all intra modes other than
DC_PRED if the source variance is small. This feature is
made part of speed 1 and up.

Results on derf300: psnr -0.07%, speedup about 1-2%

Also uses the source variance to fine-tune the early
termination criteria when FLAG_EARLY_TERMINATE is on.
This feature is made part of speed 2 and up.

Results on derf300: psnr -0.52%, speedup about 5-7%

Change-Id: I59e38aa836557cfa5405ae706fc64815cbfe4232

This changeset allows to remove vp9_switchable_interp and
vp9_switchable_interp_map arrays and make code much clear. Actually we
still have to use these mapping but only inside read_interp_filter_type and
write_interp_filter_type functions.

Change-Id: I4026c6f8c4acefba6c81421b7bacbaa52cc45f50

Cons bw/bh parms that should have been const. Additional formatting.

Change-Id: Icd36a5c9dc17dadd7284315ac0d6fef1a565ca16

Change-Id: I428c4d42212b757112e3acfe5b81314cfbb5fd6b

Consistent names with TX_SIZE, TX_MODE, and TX_MODE.

Change-Id: I79592218bf5a40ace89197a34a06ee7de581ed8d

Using it instead of long unclear verbose check
"mbmi->ref_frame[0] != INTRA_FRAME".

Change-Id: I9c7b4b3797942fa962bf3ba7460fff3084beabe9

Change-Id: I0e9329490828684a4fd46f540d89114cc68e8407

Change-Id: I73b59d7699a8e7e7acd3bf8041cb6c98ce9ba4bf

Change-Id: I27471768980fc631916069f24bc7c482a5c9ca17

Adds a function to compute source variance for various
sb_types to be used for pruning mode and partition searches.
[The existing activity measure function is currently specialized
for only 16x16 MBs and needs to be updated].

Change-Id: I22a41e6f1430184201487326fdbebb9b47e6fc24

If the partition is out of partition size range, we don't
need to process small partition information.

Change-Id: Ice9bfbbdebe1f2ef79271a3aee17de0ed4608376

use_min_partition_size and use_max_partition_size are not used
currently, and could be added back if needed later.

Change-Id: Ib22a9c06b064567a7c1d6d5445567ed77e0d3acc

Change-Id: Ib4e4b41094b54874ee34343dd77c0c131ceed9d2

This commit removes redundant arguments passing in the function of
rd_pick_reference_frame. This resolves the clang warnings about
potential use of uninitialized values.

Change-Id: Ic68f949a9f8fcd0a583786b0c75321104ea44739

Refactor the frame buffer referencing in choose_partition and make
it consistent with other places. This means to prevent potential
issues when we extend reference frame buffer.

Change-Id: I5ff33ed5f671e1f4cc7049622212769a9b4578d9

Removed unnecessary code lines, replaced switch with an if,
fixed spelling errors and formatting.

Change-Id: Ie48aa4604aa0ed48362ca359d792fb21b2ec1dc6

Change-Id: I10bf06e3a3d5271221ae6a42a36074d01d493039

Change-Id: I6aa4191935aa93461a07c41b59fdae1eb5f5f107

Speed feature experiment to set an upper and lower
partition size limit based on what has been seen
in spatial neighbors.

This seems to gives quite reasonable speed gains in local
(10-15%) and when used with speed 0 the losses are small
(0.25% derf, 0.35% stdhd). However, for now I am only
enabling it on speed 1 as there may be clashes with the existing
temporal partition selection in speed 2.

Using a tighter min / max around the range derived from the
neighbors increases speed further but at the cost of a
bigger quality loss. However,  I think this spatial method could
be combined with data from either the last frame or a variance
method (or both) to refine the range of minimum and maximum
partition size. I.e. consider the min and max from spatial and
temporal neighbors and the variance recommendation.

Change-Id: I1b96bf8b84368d6aad0c7aa600fe141b4f07435f

This option exists in VP8, and it was rewritten in VP9 to support
skipping on different partition levels. After prediction is done,
we can check if the residuals in the partition block will be all
quantized to 0. If this is true, the skip flag is set, and only
prediction data are needed in reconstruction. Based on DCT's energy
conservation property, the skipping check can be estimated in
spatial domain.

The prediction error is calculated and compared to a threshold.
The threshold is determined by the dequant values, and also
adjusted by partition sizes. To be precise, the DC and AC parts
for Y, U, and V planes are checked to decide skipping or not.

Test showed that
1. derf set:
when static-thresh = 1, psnr loss is 0.666%;
when static-thresh = 500, psnr loss is 1.162%;
2. stdhd set:
when static-thresh = 1, psnr loss is 1.249%;
when static-thresh = 500, psnr loss is 1.668%;

For different clips, encoding speedup range is between several
percentage and 20+% when static-thresh <= 500. For example,
clip            bitrate  static-thresh psnr    time
akiyo(cif)       500        0          48.923  5.635s(50f)
akiyo            500        500        48.863  4.402s(50f)

parkjoy(1080p)   4000       0          30.380  77.54s(30f)
parkjoy          4000       500        30.384  69.59s(30f)

sunflower(1080p) 4000       0          44.461  85.2s(30f)
sunflower        4000       500        44.418  78.1s(30f)

Higher static-thresh values give larger speedup with larger
quality loss.

Change-Id: I857031ceb466ff314ab580ac5ec5d18542203c53

Removing unused constants, macros, and function declarations. Using
ROUND_POWER_OF_TWO macro, vp9_zero, vp9_copy where possible. Moving
#include from *.h to *.c. Merging for loops for motion vectors.

Change-Id: Ic3bf841764a2bb177128bb3a6d7aa8f68229cd13

Simplified the code that extracts and uses the motion
vectors for the 4 sub-partitions in rd_pick_partition.

Change-Id: Iaf698ef7ee3aef9edd59015e1ae065dd359b17d9

The feature that uses small partition results as a measure to skip
mode evaluation at larger partition requires the flags to be reset.
The reset was missing in the code path that calls rd_use_partition().

Change-Id: Ia0a3a0aee1a862b6e2333d596808db7c48033d50

Change-Id: Id4138293efeac4503b2e01ce7a6c150a5abeef77

Counts are separate from frame context. We have several frame contexts but
need only one copy of all counts.

Change-Id: I5279b0321cb450bbea7049adaa9275306a7cef7d

Several consecutive for loops executed over the same
index range, so I rolled them into one.

Change-Id: I5cfcc8c38c738478965768409cca9d09adf224e1

many structures use bw and bh and they have different meanings.   This cl attempts
to start this clean up and remove unneccessary 2 step look up log and then
shift operations...

also removed partition type multiple operation code in bitstream.c.

Change-Id: I7e03e552bdfc0939738e430862e3073d30fdd5db

Moving common encoder/decoder code to update_tx_counts. Also renaming
vp9_get_pred_probs_tx_size to get_tx_probs2 and adding get_tx_probs to
call vp9_get_pred_context_tx_size inside read_selected_tx_size only once
(twice before).

Change-Id: Ia50247f3893de88ef8e9041b0d44be44a40aaa4d